American Weigh AMW-1000 Digital Bench Jewelry Scale 1000×0.1g

Features: Large stainless steel weighing surface Tare feature. Simple 4-key operation Hold feature 4 weighing modes: Grams, Pennyweights, Troy Ounces, Ounces
Click HERE to purchase the *AC Adapter Sold Seperate

Capacity	1000g / 35.27oz / 32.15ozt / 643.08dwt
Readability	0.1g / 0.01oz / 0.01ozt / 0.1dwt
Scale Dimensions	6.2 x 7.2 x 1.6 ”
Platform Dimensions	6 x 6 “
Warranty Calibration	10 Year Limited Warranty 1000g Calibraton weight not included. To purchase CLICK HERE
Power	9V Battery (included) or AC-Adapter (sold seperate)

AMW-BENCH Manual

Thank you for purchasing the American Weigh AMWBENCH

series digital tabletop scale. Please read

all operating instructions carefully before use. This

electronic scale is a precision instrument. With normal

care and proper treatment, it will provide years of

reliable service.

Never load the scale with more than the maximum

capacity. Overloading will permanently damage it!

Avoid any exposure to extreme heat or cold. Your

scale works better when operated at normal room

temperature. Always allow the scale to acclimate to

normal room temperature for at least one hour before

use. Give your scale sufficient warm up time. Usually

30-60 seconds before calibration to give the internal

components a chance to stabilize.

Keep your scale in a clean environment. Dust, dirt,

moisture, vibration, air currents and a close distance to

other electronic equipment can all cause an adverse

effect on the reliability and accuracy of your scale.

Handle with care. Gently apply all items to be weighed

onto tray top. Although this scale is designed to be

quite durable, try to avoid rough treatment as this may

permanently damage the internal sensor.

Avoid shaking, dropping or otherwise shocking the

scale. This is a precision instrument and must be

handled with extreme care.Only operate the scale on a stable, vibration free

surface.

I. OPERATION

Place Scale on a horizontal flat surface.

1. Press [ON/OFF] key.

2. Wait until “0.0” is displayed.

3. Put the object(s) on the weighing platform.

4. Using the [MODE] key, you can switch between the

weighing units.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place the “tare item” on the platform.

3. Press [TARE] and wait until “0.0″ is displayed.

4. Add the “net-weight-item”.

III. CALIBRATION

Calibration is NOT required before first use. Only

calibrate if scale is not weighing properly.

**Make sure you use the correct calibration weight for

your scale or the calibration will not be accurate**AMW-500i: 500g Calibration Weight

AMW-1000: 1000g Calibration Weight

AMW-2000: 2000g Calibration Weight

a. AMW-500i Calibration Procedures

1. Press “On/Off” key to turn off the scale.

2. Press and hold the “On/Off” and “Mode” keys at the same

time until the display shows a random number. Release both

keys now.

3. Press the “On/Off” key once.

4. When the display reads “500 g”, place your 500g calibration

weight on the scale.

5. Press “On/Off” again. The display should read “PASS”.

You can now turn off your scale.

b. AMW-1000 / AMW-2000 Calibration Procedures

1. Turn the scale ON and wait for the LCD to flash 88888.

2. While the LCD still shows 88888, press and hold the Mode

key. You may release it once the LCD displays CAL.

3. The LCD will now display the required weight for calibration

(ie 1000g for AMW-1000, 2000g for AMW-2000).

4. Place the required calibration weight onto the platform.

5. The LCD will automatically display PASS then turn off.

Calibration is complete!Please check the availability of weights with your scale

supplier.

IV. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display]

Elimination of errors

Nothing, Battery-Symbol, [lo] or [88888]

Change the batteries.

[OL-d]

try recalibrating the scale as shown above.

The scale has been overloaded. You can

[EEEEE]

excessive load immediately!

You are overloading the scale. Remove the[UNST]

Use the scale in a more stable position